[NSRCA-discussion] WOW - Brio maiden

Dean Pappas d.pappas at kodeos.com
Fri Dec 15 07:54:32 AKST 2006


Hi Stu,
Yes,  it's easy now, but back in the eighties Nat and I were discussing this same experiment with a P8, as a fair number of P8s trimmed beautifully, while others had this canopy pull with right rudder and a belly push with left rudder. I've never seen a plane where it was the opposite, but with a reverse pitch prop, a left-thrust adjustment, and two swapped wires we may be able to tell once and for all.

Kelly,
What Dave wrote has worked more than once.
What I believe Don S wrote was that if you are carrying left aileron trim for level flight, then twist the wings to eliminate the aileron trim.
This may help or eliminate the slow left roll on power-off vertical dives. If you don't have that problem to begin with, then never mind.
The different pull-push with rudder may be affected, but before you try either approach, look carefully for wing-to-stab twist as viewed from the front of the plane.
Dean

Dean Pappas
Sr. Design Engineer
Kodeos Communications
111 Corporate Blvd.
South Plainfield, N.J. 07080
(908) 222-7817 phone
(908) 222-2392 fax
d.pappas at kodeos.com


-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Stuart
Chale
Sent: Friday, December 15, 2006 10:06 AM
To: 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] WOW - Brio maiden


Doesn't help your Phoenix 8 but how about a pusher prop on an electric?  You
can change direction on the electric motor and see how that affects the trim
problems.
Stuart

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Dean Pappas
Sent: Friday, December 15, 2006 9:59 AM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] WOW - Brio maiden

Nat,
You're absolutely right! That's why you should pick up a copy of February's
Flyng Models.
I still wish we'de had a backwards crank for an OS FSR to test in a Phoenix
8 with the same issue.

Dean

Dean Pappas
Sr. Design Engineer
Kodeos Communications
111 Corporate Blvd.
South Plainfield, N.J. 07080
(908) 222-7817 phone
(908) 222-2392 fax
d.pappas at kodeos.com


-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Nat Penton
Sent: Thursday, December 14, 2006 11:10 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] WOW - Brio maiden


Kelly
Contra rotating props would solve the knife edge trim needs. Congratulations

you have a straight airplane.  Nat

----- Original Message ----- 
From: "Kelly Regan" <kelly.regan2 at verizon.net>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Sent: Thursday, December 14, 2006 8:43 PM
Subject: [NSRCA-discussion] WOW - Brio maiden


> All I can say is WOW !!!
>
> I flew the Brio today and what a blast!  The first flight was pretty
> much uneventful. A couple clicks here and there and the plane flew
> great!  The OS 140 has PLENTY of power and started right up!
>
> During the second flight after about 8 minutes the pipe slipped out
> of the coupler and I had to land. A little rough, with a bounce but no
> damage. The rudder is so sensitive that I over corrected a bit
> and the nose dropped down suddenly and I touched down a little
> harder then I would like.
>
> The third flight was all joy! I fixed my pipe problem and I could not
> believe how nice and smooth this plane made me look!
>
> A few things that jumped out that need trimming...
>
> The balance seems fine at 8" from the leading edge at the root.
>
> It seems to have a bit to much right thrust with the 16.5 x 12 2 blade
> prop but I think that can be mixed out for now until I see how it acts
> with other props.
>
> In knife edge going right with the canopy facing me it pushes a bit to
> the wheels. In knife edge going left with the canopy facing me it
> pulls just a little to the canopy.
>
> I will start working my way through the trimming guide next time out.
>
> Thanks again for everyones help!
>
> -- 
> ______________________________________________
>
> Kelly Regan
> www.reganbrothers.com
> Home Page: http://mysite.verizon.net/vze6uror/
> ______________________________________________
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>
>
> -- 
> Internal Virus Database is out-of-date.
> Checked by AVG Free Edition.
> Version: 7.1.409 / Virus Database: 268.13.20/508 - Release Date: 
> 10/31/2006
>
> 



-- 
Internal Virus Database is out-of-date.
Checked by AVG Free Edition.
Version: 7.1.409 / Virus Database: 268.13.20/508 - Release Date: 10/31/2006

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion



More information about the NSRCA-discussion mailing list