[NSRCA-discussion] JR 8711

wgalligan wgalligan at goodsonacura.com
Mon Mar 19 09:34:47 AKDT 2007


Hmmmm interesting.... maybe R/C tractor pulling could benefit from these new servo's.

WG
. 
  ----- Original Message ----- 
  From: Stuart Chale 
  To: 'NSRCA Mailing List' 
  Sent: Monday, March 19, 2007 12:29 PM
  Subject: Re: [NSRCA-discussion] JR 8711


  Are you kidding?  You can use it to pull off prop washers, pull engine bearings, just attach it to a wall (bearing) of your house and have it push down on your foam cores while they cure, connect it to your Higley wire bender to make landing gear, garage door opener.  It should have los of uses J

   

  Stuart

   


------------------------------------------------------------------------------

  From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ed Alt
  Sent: Monday, March 19, 2007 12:06 PM
  To: NSRCA Mailing List
  Subject: Re: [NSRCA-discussion] JR 8711

   

  No more than you would need for an 8611A and an 8411 together.  It really depends on what you're asking it to do.  What application would it have in a pattern airplane?  

   

  Ed

    ----- Original Message ----- 

    From: wgalligan 

    To: NSRCA Mailing List 

    Sent: Monday, March 19, 2007 7:44 AM

    Subject: Re: [NSRCA-discussion] JR 8711

     

    How much battery power is going to be required to make these babies talk?

     

     WG

      ----- Original Message ----- 

      From: Bob Richards 

      To: NSRCA Mailing List 

      Sent: Monday, March 19, 2007 7:31 AM

      Subject: Re: [NSRCA-discussion] JR 8711

       

      If I just did my math right (its still early for me) with a 1 foot servo arm, it could lift 2 lbs. With a one inch arm, 25 lbs.

       

      Yeah, it will warp something alright. We will need to pay serious attention to how these servos get mounted.

       

      Bob R.



      mike mueller <mups1953 at yahoo.com> wrote:

         Yikes with a number like that maybe we can start eliminating hinging the ailerons and go with wing warping. Mike

        Zoro1024 at aol.com wrote: 

        I hope this is not taken as an Advertisement, but I just received an email that the JR 8711's are out.  My gosh it's got 400 in oz. + on 6 volts.  If I had a surface hang up I think it'd probably bust my plane in half:-)

         

         

        Mike H.






------------------------------------------------------------------------

        AOL now offers free email to everyone. Find out more about what's free from AOL at AOL.com. 

        _______________________________________________
        NSRCA-discussion mailing list
        NSRCA-discussion at lists.nsrca.org
        http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

         


------------------------------------------------------------------------

        TV dinner still cooling?
        Check out "Tonight's Picks" on Yahoo! TV._______________________________________________
        NSRCA-discussion mailing list
        NSRCA-discussion at lists.nsrca.org
        http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

       


--------------------------------------------------------------------------

      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------------

    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion



------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070319/ceb03890/attachment.html 


More information about the NSRCA-discussion mailing list