<br><font size=2 face="sans-serif">Man, you are FAST! </font>
<br><font size=2 face="sans-serif">I just got out of a meeting and wondered if you'd gotten my message, and here you had already tried it!</font>
<br>
<br><font size=2 face="sans-serif">Are you going to build your Entropy this fast? I recommend waiting for the glue to dry before flying.</font>
<br>
<br><font size=2 face="sans-serif">--Lance</font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td>
<td><font size=1 face="sans-serif"><b>"Van - E-Mail LIST" <extra330@tampabay.rr.com></b></font>
<br><font size=1 face="sans-serif">Sent by: discussion-request@nsrca.org</font>
<p><font size=1 face="sans-serif">09/11/2002 02:02 PM</font>
<br><font size=1 face="sans-serif">Please respond to discussion</font>
<br>
<td><font size=1 face="Arial"> </font>
<br><font size=1 face="sans-serif"> To: <discussion@nsrca.org></font>
<br><font size=1 face="sans-serif"> cc: </font>
<br><font size=1 face="sans-serif"> Subject: Re: Fiberglass Question - Please Educate me !</font></table>
<br>
<br>
<br><font size=2 face="Times New Roman">For what it's worth Lance, the Saran Wrap worked like a CHAMP ! Just pulled the first two rings, and they look damn nice, if I do say so. . . . .</font>
<br>
<br><font size=3 face="Times New Roman"> </font><font size=2 face="Times New Roman">Thanks for all the input from everyone.</font>
<br>
<br><font size=2 face="Arial">________________________________________________</font>
<br>
<br><font size=3 face="Times New Roman"> </font><font size=2 face="Arial">Van Flowers</font>
<br><font size=2 face="Arial">AMA: 6216 IMAC: 2229 </font>
<br><font size=2 face="Arial">IMAA: 26019 NSRCA: 2778</font>
<br><font size=2 face="Arial"> www.rc-aerobatics.com</font>
<br>
<br><font size=3 face="Times New Roman"> ----- Original Message ----- </font>
<br>
<br><font size=3 face="Times New Roman"><b>From:</b> s.vannostrand@kodak.com </font>
<br>
<br><font size=3 face="Times New Roman"><b>To:</b> discussion@nsrca.org </font>
<br>
<br><font size=3 face="Times New Roman"><b>Sent:</b> Wednesday, September 11, 2002 12:48 PM</font>
<br>
<br><font size=3 face="Times New Roman"><b>Subject:</b> Re: Fiberglass Question - Please Educate me !</font>
<br>
<br>
<br>
<br><font size=2 face="Times New Roman">Van, in after the car wax, apply some PVA. YOu can buy this at craft stores in small quantities near where they sell plaster/molding resing/etc. Michael's and HobbyLobby are in Dallas. Apply two coats of PVA. From a sprayer if you can. If you don't have air equip, buy a Precor can ($3) or use an old atomizer. PVA dissolves in water so after laying up the parts, you can soak the mold/part in warm water and make it easier to remove. Gray's right on the difficulty here. YOu wouldn't belive the trouble we've had in making our own carbon mufflers. </font><font size=3 face="Times New Roman"> </font>
<br>
<br><font size=2 face="Times New Roman">Another idea I have, but haven't tried, is to wrap the PVC molding pipe with Saran wrap, lay up the part, remove the pipe and then peel off the Saran wrap from the inside. THis would be very easy.</font>
<br>
<br>