<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2800.1170" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT face=Arial size=2>MKD0815 Offset Aluminum Horn Medium
size</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2><A
href="http://www.centralhobbies.com/control_linkage/control_horns/mkd.html">http://www.centralhobbies.com/control_linkage/control_horns/mkd.html</A></FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>They work well I have them on my
Flashdance...(Artistic Aero) model huge control deflections and huge
surfaces.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>I also ran them on my Hydeaway on the
Rudder...Super Easy to install...I use a Dermal Router attachment and
countersink a piece of ply into the surface. By the way I stick a piece of balsa
in the surface also then router it out....Sand flush and its a done deal...Never
had an issue yet..Hydeaway has around 500 flights and last I heard its keeping
the new owner very happy.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>So they are an option.....</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>TN</FONT></DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=tkeithb@comcast.net href="mailto:tkeithb@comcast.net">Keith Black</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Tuesday, September 02, 2003 9:57
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Control horns, is it just me
or... ?</DIV>
<DIV><BR></DIV>
<DIV><FONT face=Arial size=2>When it comes to control horns for pattern planes
it seems to me that some of the most commonly used choices have a major
flaw.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>On my last plane I used the MK Aluminum
Horns on all surfaces except for the rudder where I used the IM pull-pull
horns. Both of these are nice horns except they have a major flaw when using a
pull-pull setup. The flaw is that the little black plastic arm that screws
onto the horn and connects to the clevis is so short that it doesn't extend
out over the hinge line. I know that with pull-pull systems it isn't
*absolutely* necessary for the connection to be exactly above the hinge, but
the further back it is the more slack there will be in the cable that is not
pulling. In my opinion with these horns the connection point is too far
away from the hinge unless the horn is virtually mounted on the control
surface bevel (especially when it comes to rudder). This can easily be seen in
these "instructions" for installing the MK horns <A
href="http://www.centralhobbies.com/buildingtips/mkhorns/mkhornsinst.html">http://www.centralhobbies.com/buildingtips/mkhorns/mkhornsinst.html</A>.
Notice that in this picture there surface isn't beveled yet and the horn is
almost on the edge.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>On my new plane I wanted to avoid this problem so
I did some searching to find a better solution. To begin with I looked for a
longer arm to connect to the MK horn, one that would extend out to the hinge
line. I found two options from Sullivan but both require too big of a horn
thread (6-32 and 8-32). My search then led me to two other choices that seem
to be good alternatives. The first is the ZNLine aluminum control horns, but
these are apparently only distributed by ZNLine (<A
href="http://www.znline.com/produits.php?langue=english&cle_menus=1025879382&cle_data=1025901639">http://www.znline.com/produits.php?langue=english&cle_menus=1025879382&cle_data=1025901639</A>)
which means an international order. The other solution I've found is by
</FONT><FONT face=Arial size=2><FONT face="Times New Roman" size=3><FONT
face=Arial size=2>RC Model Enterprises</FONT> <FONT face=Arial
size=2>(</FONT></FONT><A
href="http://home.att.net/~rc-enterprises/rcme_014.htm">http://home.att.net/~rc-enterprises/rcme_014.htm</A>)
but these control horns seem very pricey!</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>If anyone could point me to a longer 3mm
connecting arm that will fit on the MK and IM horns I'd be happy (BTW, I've
used the MK BB connectors on the MK horn and they still aren't really long
enough).</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Is it just me, or have others experienced this
dilemma as well?</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Thanks,</FONT></DIV>
<DIV><FONT face=Arial size=2>Keith Black</FONT></DIV>
<DIV> </DIV></BLOCKQUOTE></BODY></HTML>