<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2800.1170" name=GENERATOR></HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT face=Arial size=2>Georgie</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>I had kevlar pull/pull on my Prophecy for over two
years with no incidence at all. Don't be afraid.... kevlar is
good! Its so easy to use and if you every did need a field repair it
is so easy to re rig. Tie it off and a drop of c/a on the knot and
go flying again.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Wayne</FONT></DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=geobet@gis.net href="mailto:geobet@gis.net">george kennie</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Tuesday, November 25, 2003 11:57
AM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: CTE</DIV>
<DIV><BR></DIV>Sorry to disagree here, but it would appear that the conclusion
being drawn by the respondants is that the pushrod expansion and contraction
is the major cause of the problem. Not so, in my experience! Going to
pull-pull cables, whether they be steel or kevlar thread will not get rid of
the elevator trim change under consideration here.The coefficient of thermal
expansion between the cables, which is very small, and the balsa in the fuse,
which is significantly greater(glass too) will generate a differential of
sufficient magnitude that the "devil" will still attack you when you least
expect it. <BR>The best solution that I have observed is to put the servos in
the stabs. Short of this, I have been using servos mounted just at the L.E. of
the stab and using a very short pushrod(approx. 6"). My current thinking is
that I will still mount the servo in the same area and go with cables.Very
light and direct. As regards Kevlar, I currently have a pattern practise ship
that I do almost all of my flying with that has kevlar on the rudder and it
has two years of mucho sequences to it's credit with no apparent wear or
abrasions to the thread. At this point in time I have still not acquired the
necessary intestinal fortitude to use kevlar on the elevator. <BR>Georgie
<P>Amir Neshati wrote:
<BLOCKQUOTE TYPE="CITE">
<STYLE></STYLE>
<FONT face=Arial><FONT size=-1>Pull-pull will eliminate the trim
change...</FONT></FONT> <FONT face=Arial><FONT
size=-1>Amir</FONT></FONT>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message -----</DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=natpenton@centurytel.net
href="mailto:natpenton@centurytel.net">Nat Penton</A></DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A></DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Monday, November 24, 2003 7:24
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> CTE</DIV> <FONT
face=Arial><FONT size=-1>Gray what is the CTI for balsa ? I have carbon
push rods / balsa fuse and my elev trim moves around considerably. I
suppose it is because of humidity variation between the shop and outdoors
?? The pushrods are 50" long.
NatPenton</FONT></FONT> </BLOCKQUOTE></BLOCKQUOTE></BLOCKQUOTE></BODY></HTML>