<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<html>
<head>
<meta name=Generator content="Microsoft Word 11 (filtered)">
<style>
<!--
/* Font Definitions */
@font-face
{font-family:Tahoma;
panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman";}
a:link, span.MsoHyperlink
{color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{color:purple;
text-decoration:underline;}
span.EmailStyle17
{font-family:Arial;
color:navy;}
@page Section1
{size:8.5in 11.0in;
margin:1.0in 1.25in 1.0in 1.25in;}
div.Section1
{page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=purple id="role_body" bottomMargin=7
leftmargin=7 topmargin=7 rightMargin=7>
<div class=Section1>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'>It’s not getting any fuel. </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'>Try blowing into the fuel line that goes
to the high speed needle assembly. You should be able to blow through it. Make
sure needle is 1 ¾ to 2 turns out. </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<div>
<div class=MsoNormal align=center style='text-align:center'><font size=3
face="Times New Roman"><span style='font-size:12.0pt'>
<hr size=3 width="100%" align=center tabindex=-1>
</span></font></div>
<p class=MsoNormal><b><font size=2 face=Tahoma><span style='font-size:10.0pt;
font-family:Tahoma;font-weight:bold'>From:</span></font></b><font size=2
face=Tahoma><span style='font-size:10.0pt;font-family:Tahoma'>
discussion-request@nsrca.org [mailto:discussion-request@nsrca.org] <b><span
style='font-weight:bold'>On Behalf Of </span></b>Prmoore@aol.com<br>
<b><span style='font-weight:bold'>Sent:</span></b> Saturday, 5 June 2004 2:19
PM<br>
<b><span style='font-weight:bold'>To:</span></b> discussion@nsrca.org<br>
<b><span style='font-weight:bold'>Subject:</span></b> YS 140L not starting</span></font></p>
</div>
<p class=MsoNormal><font size=3 face="Times New Roman"><span style='font-size:
12.0pt'> </span></font></p>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:black'>Engine doesn't want to fire. Symptoms: </span></font></p>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:black'>Fuel draw not the best, very little
pressure in the tank, compression seems OK. When we first pulled the cowl
the fuel was to the filter which was the high spot in the line, after some
fidgeting (not sure why) the fuel line had visible fuel to the engine. </span></font></p>
</div>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:black'>Removed the glow plug, put a few drops of
fuel in the cylinder still basically wouldn't fire. There we a couple of
very minor puts while turning with the starter after putting the fuel
drops in the cylinder. Pulled valve cover, valve gap not the
problem. Glow plug glows, check valve is in the correct
direction. If you put your finger over the pipe
exhaust can't feel any pressure pulses as we turned the engine over.
This engine hasn't been run since comming back from YS (supposedly rebuilt).</span></font></p>
</div>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:black'> </span></font></p>
</div>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:black'>Phil</span></font></p>
</div>
</div>
</div>
</body>
</html>