<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD><TITLE>Webra 1.45 problem</TITLE>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2800.1400" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><SPAN class=028492923-24072004><FONT face=Arial color=#0000ff size=2>Amen
to Bob Pastorello comments, check the lines and tank first.... Charlie
Rock</FONT></SPAN></DIV>
<BLOCKQUOTE dir=ltr style="MARGIN-RIGHT: 0px">
<DIV class=OutlookMessageHeader dir=ltr align=left><FONT face=Tahoma
size=2>-----Original Message-----<BR><B>From:</B> discussion-request@nsrca.org
[mailto:discussion-request@nsrca.org]<B>On Behalf Of </B>Bob
Pastorello<BR><B>Sent:</B> Saturday, July 24, 2004 3:41 PM<BR><B>To:</B>
discussion@nsrca.org<BR><B>Subject:</B> Re: Webra 1.45
problem<BR><BR></FONT></DIV>
<DIV><FONT face=Arial size=2>Make sure your clunk inside the tank isn't
tangling up on the vent line, or touching the back of the tank, OR that
there's a hole in the fuel pickup line where it goes on the tube in the
stopper.....any of those would cause a time-into-flight
failure...</FONT></DIV>
<DIV><BR>Bob Pastorello<BR><A
href="mailto:rcaerobob@cox.net">rcaerobob@cox.net</A><BR><A
href="http://www.rcaerobats.net">www.rcaerobats.net</A></DIV>
<DIV> </DIV>
<DIV> </DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=GAA@owt.com href="mailto:GAA@owt.com">Gordon Anderson</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Saturday, July 24, 2004 3:37
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Webra 1.45 problem</DIV>
<DIV><BR></DIV><!-- Converted from text/rtf format -->
<P><FONT face="Comic Sans MS">I'm having a problem with my Webra 1.45 and I
hope someone can help me out. I have a new Hydeout (thanks to the guys that
gave me the control throw advice!) with a new Webra 1.45. Below are
the details on the motor setup:</FONT></P>
<P><FONT face="Comic Sans MS">Prop: APC 17x2</FONT> <BR><FONT
face="Comic Sans MS">Fuel: Magnum #1</FONT> <BR><FONT
face="Comic Sans MS">Plug: OS #8</FONT> <BR><FONT face="Comic Sans MS">Pipe:
Greves</FONT> <BR><FONT face="Comic Sans MS">Mount: Hyde type soft mount and
nose ring</FONT> <BR><FONT face="Comic Sans MS">Tank: Tetra 20oz, on CG of
model</FONT> <BR><FONT face="Comic Sans MS">I have about 2/3 of a gallon of
fuel run through the motor, this Webra uses the regular carb with the high
speed and low speed needles.</FONT></P>
<P><FONT face="Comic Sans MS">The problem is the motor dies when I roll from
inverted to upright. This happens mostly after I have been at idle for a
while. I'm flying the advanced routine and it dies during the roll out on
the bunt and the bottom of the double I even the slow roll. I have never
made it more than about 3 minutes into a flight.</FONT></P>
<P><FONT face="Comic Sans MS">It seems to run fine on the down lines at
idle, like in the stall turns and the outside square loop.</FONT> <BR><FONT
face="Comic Sans MS">When it dies it sounds like someone pulled the fuel
line off the engine, it just un winds. We tried leaning the low speed
needle, replaced the tank internal fuel line to the clunk.</FONT></P>
<P><FONT face="Comic Sans MS">Any advice?</FONT> </P>
<P><FONT face="Comic Sans MS">--Gordon</FONT>
</P></BLOCKQUOTE></BLOCKQUOTE></BODY></HTML>