<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2800.1491" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY id=role_body style="FONT-SIZE: 10pt; COLOR: #000000; FONT-FAMILY: Arial"
bottomMargin=7 bgColor=#ffffff leftMargin=7 topMargin=7 rightMargin=7>
<DIV>Peter,</DIV>
<DIV> </DIV>
<DIV>Run some CA into the sockets. Do that by rotating the socket after
every drop</DIV>
<DIV>and run a beat every 90º. Just a drop at a time. Don't run in too much at
once </DIV>
<DIV>and use a little accelerator. Make sure the CA is well cured before
inserting the tube.</DIV>
<DIV>If it gets too tight wrap some sand paper around a broom handle and sand it
out </DIV>
<DIV>to the fit you like. </DIV>
<DIV> </DIV>
<DIV>Karl G. Mueller<BR><A
href="mailto:kgamueller@rogers.com">kgamueller@rogers.com</A><BR></DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=Rcmaster199@aol.com
href="mailto:Rcmaster199@aol.com">Rcmaster199@aol.com</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Monday, February 28, 2005 8:50
AM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: PBG carbon wing tube for
IMPACT</DIV>
<DIV><BR></DIV><FONT id=role_document face=Arial color=#000000 size=2>
<DIV>
<DIV>In a message dated 2/28/2005 5:32:19 AM Eastern Standard Time, <A
href="mailto:pentagon.systems@bigpond.com">pentagon.systems@bigpond.com</A>
writes:</DIV>
<BLOCKQUOTE
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px solid"><FONT
style="BACKGROUND-COLOR: transparent" face=Arial color=#000000 size=2><BR>Hi
All,<BR><BR>I have a PBG 30mm carbon tube for my IMPACT which is 35 grams
lighter than<BR>the original. Unfortunately it is a little loose in the
existing wing<BR>sockets. What is a good technique to fix this? I don't want
to add anything<BR>to the tube itself otherwise I won't be able to use the
carbon sleeve<BR>supplied. <BR><BR><BR>Regards,<BR><BR>Peter
<BR></FONT></BLOCKQUOTE></DIV>
<DIV></DIV>
<DIV>Peter, I have run some ca on the tube to tighten up loose fits. Then a
little fine sanding will produce the nice slip fit you are looking for</DIV>
<DIV> </DIV>
<DIV>MattK</DIV></BLOCKQUOTE></FONT></BODY></HTML>