<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2800.1505" name=GENERATOR></HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT size=2>Dave,</FONT></DIV>
<DIV><FONT size=2></FONT> </DIV>
<DIV><FONT size=2>Try a little heat with a torch while you have the tension
from the puller</FONT></DIV>
<DIV><FONT size=2>on the drive washer. The aluminum drive washer will expand
more with a </FONT></DIV>
<DIV><FONT size=2>little heat then the steel shaft will. If that doesn't work,
use the hammer </FONT></DIV>
<DIV><FONT size=2>and the heat. :-)</FONT></DIV>
<DIV><FONT size=2></FONT> </DIV>
<DIV><FONT size=2>Karl G. Mueller<BR><A
href="mailto:kgamueller@rogers.com">kgamueller@rogers.com</A><BR></FONT></DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=d.wartel@comcast.net href="mailto:d.wartel@comcast.net">David
Wartel</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Saturday, June 18, 2005 9:32
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: </DIV>
<DIV><BR></DIV>
<DIV><FONT face="Arial Narrow" size=4>I hope you're joking! I just emailed a
friend about this and he said, "take your time and think things through before
you resort to a hammer." (!)</FONT></DIV>
<DIV><FONT face="Arial Narrow" size=4></FONT> </DIV>
<DIV><FONT face="Arial Narrow" size=4>Also: I'm using the Boca sealed SS
bearing. What was the concensus regarding leaving/removing the
seal(s)?</FONT></DIV>
<DIV><FONT face="Arial Narrow" size=4></FONT> </DIV>
<DIV><FONT face="Arial Narrow" size=4>Dave</FONT></DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=geobet@gis.net href="mailto:geobet@gis.net">george kennie</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=discussion@nsrca.org
href="mailto:discussion@nsrca.org">discussion@nsrca.org</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Saturday, June 18, 2005 9:17
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: </DIV>
<DIV><BR></DIV>When it's good and tight, hit the end of the puller screw a
good belt with a hammer! The abrupt shock will bust it free.
<P>David Wartel wrote:
<BLOCKQUOTE TYPE="CITE">
<STYLE></STYLE>
<FONT face="Arial Narrow"><FONT size=+1>I'm replacing the bearing in a
Webra 1.45. All of the "difficult" disassembly is done: the circlip, wrist
pin etc., but I'm having trouble removing the prop drive hub. I'm assuming
this is a press fit and am using a gear puller, but even tightening the
tool as much as I can, the hub stays put.</FONT></FONT> <FONT
face="Arial Narrow"><FONT size=+1>Is there a trick to removing
it?</FONT></FONT> <FONT face="Arial Narrow"><FONT size=+1>Thanks,
Dave</FONT></FONT></BLOCKQUOTE></BLOCKQUOTE></BLOCKQUOTE></BODY></HTML>